There are currently no product reviews.
Everything was ok with the manual. If I have a small complaint, is that I ordered it during the weekend and I think you guys were closed. But I did receive it late Sunday. I will surely order from you again
Best Service! Very fast and easy to handle. Fast Download an you can come back every day to download again
Very good quality, no parts are missing and everthing is readable.
Thank you very much. :-)
This manual is all I need to check and repair my equipment. Thank you....
sorry for my english...the service given by O.M.com is perfect for content and codition...!!!
thank's a lot!!!
PURITY ADJUSTMENT ADJUSTMENT PRECAUTION:
1 PURITY ADJ. 1. Receive GREEN-ONLY signal. Adjust the beam current to about 500 ÂµA. 2. Degauss CRT enough with the degausing coil.
Make sure TV Set is in "Normal Condition" before switch to service mode for adjustNo. point Adjusting procedure/conditions Waveform and others ment.
Note: Follow the Job Instruction Sheet to adjust the magnetic field. 3. Maintain purity magnet at the zero magnetic field and keep the static convergence roughly 1 Tuner IFT 1. Get tuner ready to receive the CH. E 9 adjusted. ( PRESET ) signal,but with no signal input. 4. Observe the points a, b as shown in Fig. 4-1 Adjust the PLL data.
Oscilloscope IF OUT
No. point Adjusting procedure/conditions Waveform and others
2. Connect the sweep generator's output cable to 1n60 1000p through microscope. Adjust landing to the 10k 5. Orient the raster rotation to 0 eastward.
the tuner antenna. ( RF SWEEP ) rank A requirements. 6. Tighten up the deflection coil screws. 3. Adjust the sweep generator's to 80dBuV. 4. Connect the response lead ( use LOW IMPED-
ANCE probe with wave detector ; see Fig.1 ) to Â» Tightening torque: 108 20 N (11 Â± 2 kgf) A the tuner's IF output terminal. ( This terminal Fig.1 7. Make sure CRT corners landing meet the A rank requirements. If not, stick the magnet sheet must have the probe alone connected ). to correct it. 5. Set the RF AGC to 0 6 V no saturation with B Note: This adjustment must be done after the waveform. longer with a beam current over 500 ÂµA. shown in Fig. 2. -1.5+/-0.8dB Fig.2 * For the following colours press R/C RGB key to Fig. 4-2 Note: Be sure to keep the tuner cover in position
6. Adjust tuner IF coil to obtain the waveform as A = B
P C warming up the unit for 30 minutes or
during this adjustment. change. Rank "A"
(on right of the CRT)
Green-only Blue-only Red-only
2 RF-AGC 1. Receive "PAL COLOUR BAR" signal. Note: For the 50 ohm signal
TAKE OVER Â» Signal Strength: 57 Â± 1 dBÂµV (75 ohm open) strength gauge, when not POINT AD2. Connect the oscilloscope to TP201(Tunerâs AGC u s g 0 / 7 5 i m p d a n c e
JUSTMENT Terminal) as shown in Fig. 3. adapter, signal strength is
B + TP201 open).
Â» Bias box: About 4.5 V (on left of the CRT) Fig. 3 * Press R/C RGB key for 1 sec-
screen cleared (I C BUS 52Â±1dBÂµV(75 ohm open), in-
CONTROL) Oscilloscope stead of 57Â±1dBÂµV (75 ohm
0.1V Precaution: The loss of using
â impedance adapter A = B Fig. 4-3
Bias box TV Set
â Rank "A"
3. Call "AGC" mode in service mode. Adjust the ond in NORMAL MODE, the
"AGC" bus data to obtain the Tuner output pin colour will change to RGB mono drop 0.1V below maximum voltage. colour mode.
4. Change the antenna input signal to 63~67dBÂµV,
and make sure there is no noise.
5. Turn up the input signal 90~95 dBÂµV to be sure
that there is no cross modulation beat.