Shopping cart is empty
 
English Polski Spanish 
Search For a Manual
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Who's Online
There currently are 562 guests online.
Categories
Information
Featured Product
Home >> SHARP >> 14D2S Service Manual
 
 0 item(s) in your cart 

SHARP 14D2S
Service Manual


Tweet about this product and get $1.00 of store credit for instant use!
  • Contains Circuit Diagrams
  • Download
  • PDF Format
  • Complete manual
  • Language: English
Price: $4.99

Description of SHARP 14D2S Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagrams, printed circuit boards, repair tips, wiring diagrams, block diagrams and parts list. Service Manual ( sometimes called Repair Manual ) is used mainly by technicians.

If You just want to know how to use Your tv, video, mp3 player etc. You should look for Owner's Manual. After placing order we'll send You download instructions on Your email address.

The manual is available in languages:

Not yet ready
You must purchase it first

Customer Reviews
There are currently no product reviews.
Other Reviews
 V-909RX TEAC Service Manual by Sam Palermo;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
 RC666 SIEMENS Service Manual by Gabriel Popa;
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
 SC-3330 SANSUI Service Manual by Marc LO BONO;
Acurate informations inside the SM and I could repair my old Sansui SC-3330 without any problems. Thanks.
 7045 NAD Service Manual by Marc LO BONO;
I used it to repair a NAD 7030, but unfortunately, the 7045 is different ! But documentation was useful.
 STR-4800 SONY Service Manual by Marc LO BONO;
Content A4 and A3 format pages. Exactly what I needed to restore my old receiver.

Text excerpt from page 7 (click to view)
ADJUSTMENT PRECAUTION: PURITY ADJUSTMENT Make sure TV Set is in "Normal Condition" before switch to service mode for adjustNo. point Adjusting procedure/conditions Waveform and others ment.
1 PURITY ADJ. 1. Receive GREEN-ONLY signal. Adjust the beam current to about 500 µA. 2. Degauss CRT enough with the degausing coil.

a b
Note: Follow the Job Instruction Sheet to adjust the magnetic field. 3. Maintain purity magnet at the zero magnetic field and keep the static convergence roughly 1 Tuner IFT 1. Get tuner ready to receive the CH. E 9 adjusted. ( PRESET ) signal,but with no signal input. rank A requirements. the tuner antenna. ( RF SWEEP )
100k 75ohm

PIF ADJUSTMENT

No. point Adjusting procedure/conditions Waveform and others

2. Connect the sweep generator's output cable to 10k 1n60 1000p through microscope. Adjust landing to the
Oscilloscope IF OUT

Adjust the PLL data. 4. Observe the points a, b as shown in Fig. 4-1 Fig. 4-1 5. Orient the raster rotation to 0 eastward. 6. Tighten up the deflection coil screws. 3. Adjust the sweep generator's to 80dBuV. 4. Connect the response lead ( use LOW IMPED-

ANCE probe with wave detector ; see Fig.1 ) to » Tightening torque: 108 20 N (11 ± 2 kgf) A the tuner's IF output terminal. ( This terminal Fig.1 7. Make sure CRT corners landing meet the A rank requirements. If not, stick the magnet sheet must have the probe alone connected ). to correct it. 5. Set the RF AGC to 0 6 V no saturation with B Note: This adjustment must be done after the waveform. longer with a beam current over 500 µA. shown in Fig. 2. -1.5+/-0.8dB Fig.2 * For the following colours press R/C RGB key to Note: Be sure to keep the tuner cover in position Fig. 4-2

E-9 CH

6. Adjust tuner IF coil to obtain the waveform as A = B

P C warming up the unit for 30 minutes or

during this adjustment. change. Rank "A"
(on right of the CRT)

Green-only Blue-only Red-only

2 RF-AGC 1. Receive "PAL COLOUR BAR" signal. Note: For the 50 ohm signal

TAKE OVER » Signal Strength: 57 ± 1 dBµV (75 ohm open) strength gauge, when not POINT AD2. Connect the oscilloscope to TP201(Tuner’s AGC u s g 0 / 7 5 i m p d a n c e

7
7-1 7-2

(I C BUS 52±1dBµV(75 ohm open), in-2 CONTROL) Oscilloscope stead of 57±1dBµV (75 ohm

A Signal-colour screen cleared

JUSTMENT Terminal) as shown in Fig. 3. adapter, signal strength is
B + TP210 open).

0.1V Precaution: The loss of using

– impedance adapter A = B Fig. 4-3
Rank "A" –

Bias box TV Set

+

» Bias box: About 4.5 V (on left of the CRT)

Fig. 3 * Press R/C RGB key for 1 sec-

3. Call "AGC" mode in service mode. Adjust the ond in NORMAL MODE, the

"AGC" bus data to obtain the Tuner output pin colour will change to RGB mono drop 0.1V below maximum voltage. colour mode.

4. Change the antenna input signal to 63~67dBµV,

and make sure there is no noise. The TEXT "R. G. Cy" Key

5. Turn up the input signal 90~95 dBµV to be sure can be directly use to change

that there is no cross modulation beat. to other colours screen.

14D1-S/G/W 14D2-S/G

You might also want to buy

$4.99

14D2S SHARP
Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
>
Parse Time: 0.158 - Number of Queries: 110 - Query Time: 0.028