|
Who's Online
There currently are 5848 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
PURITY CONVERGENCE ADJUSTMENT
No. Adjusment point Conditions/Adjusting procedure Waveform or others
PURITY ADJ. GREEN-ONLY Adjust 1 CONVERGENC 1. Receive the "Crosshatch Pattern" signal.
beam current to ~ 500 µA. ADJ. 2. Using the remote controller, call NORMAL mode. BGR
2. Maintain purity magnet at the zero magnetic ( To be done
a b B field and keep static convergence roughly after the purity STATIC CONVERGENCE
ours. through microscope. Adjust landing to the 2. Turn the 6-pole magnet to proper opening anA rank requirements. Fig. a
3. Observe points a, b, as shown Fig. 1-1 gle in order to superpose the blue and red col-
adjusted. adjustment.) 1. Turn the 4-pole magnet to a proper opening anG R
RGB 4. Orient raster rotation 0 eastward. gle in order to superpose the green colour over 5. Tighten up deflection coil screws. the blue and red colours.
Fig. 1-1
6. Make sure CRT corners landing meet the A DYNAMIC CONVERGENCE G
» Tightening torque: 108 20 N (11 ± 2 kgf) R
rank requirements. If not, stick magnet sheet 1. Adjust convergence on fringes of the B to correct it. screen in the following steps. A Note: This adjustment must be done after a) Fig. a: Drive the wedge at point "a" and swing
deflection coil upward. warming up the unit for 30 minutes or and swing the deflection coil downward. G
Fig. b
longer with a beam current over 500 µA. b) Fig. b: Drive the wedge at points "b" and "c" R G B B A = B the deflection coil rightward.
d) Fig. d: Drive the "b" wedge deeper and swing c) Fig. c: Drive the "c" wedge deeper and swing R
Fig. 1-2 the deflection coil leftward. Rank "A"
R
Fig. c 2. Fix all wedges on the CRT and apply glass tape over them. (On right of the CRT) BGR magnet unit (purity, 4-pole, 6-pole magnets) and B magnet unit lock screw. 3. Apply lacquer to the deflection yoke lock screw, G
7
A Finally received the Red-only and Blue-only sigB Wedge "a" A = B Fig. 1-3 Lacquer Rank "A" (On left of the CRT)
nals to make sure there is no other colours on the Fig. d screen.
About 100 Deg
Wedge "c" "b"
4-pole magnet 6-pole magnet CRT neck
(21") 20cm Lacquer
Purity magnet 40cm(14")
14U10/15 14U20/25
7-1 7-2
|
|
|
> |
|