|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Up to now you are the BEST! Prompt-efficient and so reasonable ! I have been after SONY service manual for quite some time !Thank you very much ! I can recomend your service to
all my collegagues ! V.Bergfield .
;
This is a very good quality print (scan) of the original SONY service manual. The original from Sony is on very thin paper. Nevertheless it is very clear and sharp and excellent readable. I'm very satisfied to have now this rare document. I've looking for it many years (infrequent). It contains very detailed circuit diagrams, exploded views, part lists, PCB view with good readable connection lines. Very recommended.
;
A complete manual with all the needed details of calibrations and service instructions about the radio receiver.
A big deal.
Many thanks !
;
Fast delivery and good quality copy. To be recommended
;
Excellent product, very clear print. Detailed circuit and assembly diagrams - this enabled me to repair my CD player with confidence. I highly recommend this site.
PIF ADJUSTMENT CHECKING SHIPPING SETTING & CHECKING
NO POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS 1 Tuner IFT (1) Get tuner ready to receive the CH. E 9 (1) The following default data has been factory-set for the E2PROM. 10k 1n60 1000p ( PRESET ) signal, but with no signal input. Adjust the PLL data. Oscilloscope IF OUT
ITEMS DATA SETTING (2) Connect the sweep generator's output cable to 100k 75ohm LAST PROGRAM/CHANNEL 1 the tuner antenna. (RF SWEEP) FLASHBACK PROGARM/CH 1 (3) Adjust the sweep generator's to 80dBuV.
(4) Connect the response lead (use LOW Fig. 1 DIGIT 1 IMPEDANCE probe with wave detector ; see C-SYSTEM AUTO Fig.1) to the tuner's IF output terminal. S-SYSTEM *1 B/G (This terminal must have the probe alone
P C
E-9 CH
SKIP OFF connected ). AFC ON (5) Set the RF AGC to 0 6 V with no saturation COLOUR 0 (CENTER) BRIGHTNESS 0 (CENTER) Note : Be sure to keep the tuner cover in position
during this adjustment.
-1.5+/-0.8dB
VOLUME 1 with the waveform.
Fig. 2 as shown in Fig. 2.
CONTRAST 60 (MAX) (6) Adjust tuner IF coil to obtain the waveform
TINT 0 (CENTER) SHARPNESS 0 (CENTER) 2 RF-AGC (1) Receive "PAL COLOR BAR" signal. Signal Note : For the 50 ohm signal WHITE TEMP STANDARD TAKE OVER Strength: 57 ± 1dBµV (75 ohm open) strength gauge, when not
POINT (2) Connect the oscilloscope to TP201 (Tuner's using 50/75 impedance REMINDER TIMER In-active, ��:�� ADJUSTMENT AGC Terminal) as shown in Fig 3-1. adapter, signal strength is ON TIMER In-active, ��:�� (I2C BUS 52 ± 1dBµV (75 ohm OFF TIMER In-active, ��:�� CONTROL) open), instead of 57 ±
+ OSCILLOSCOPE �
LAST POWER POWER-ON 1dBµV (75 ohm open). LANGUAGE *1 THAI
TP201
0.1V
Precaution : The loss of using impedance adapter. BLUE BACK MUTE OFF +
BIAS BOX
7
� Bias Box : about 4.5V
HOTEL MODE OFF *1: PLEASE CHANGE IT BY REMOTE CONTROL
(3) Call "AG" mode in service mode. Adjust the "AG" bus data to obtain the Tuner output pin drop 0.1V below maximum voltage. (4) Change the antenna input signal to 63 ~ 67dBµV, and make sure there is no noise. (5) Turn up the input signal 90 ~ 95 dBµB to be sure that there is no cross modulation beat. Fig. 3-1
TV SET
20GT-20 21GT-20
|
|
|
> |
|