|
|
|
Who's Online
There currently are 5937 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A good manual! fast service and good qualityi for pdf document.
thanks!
 ;
Very helpful and complete manual. Maybe only one negative is schematics have sometimes unreadable name of the parts. But it's not a big problem.
;
Excellent high quality schematics brought my old Heidelberg back to life. Fast download at a reasonable price. Thanks.
;
This document is just what I was looking for, it´s very useful, it contains adjustment procedures for the final stage of the power amp and also
has a complete wiring diagram and description of the main semiconductors used in the design.
;
Dear Sirs,
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
21VR2 21VR2
PROTECTOR PERFORMANCE CHECK
No. Adjusting point 1 Beam protector Adjusting procedure/conditions 1. Receive the E-5CH (monoscope pattern) signal. 2. Set the contrast control to maximum. 3. Set the brightness control to maximum. 4. Make a short-circuit between the collector and emitter of Q851, Q852 or Q853 and make sure that the protector is activated and the stand-by mode is called. Waveform and others * Short-circuit any of the Q851, Q852 and Q853. 1
FUNCTION CHECK (VIDEO AND AUDIO)
No. Adjusting point CONTRAST key Adjusting procedure/conditions 1. Receive the E-5CH signal. 2. Select the contrast on the P-MODE screen. 3. The contrast must be changeable with the UP/ DOWN key. 1. Receive the E-12CH signal. 2. Select the colour on the P-MODE screen. 3. The colour must be changeable with the UP/ DOWN key. 1. Receive the E-5CH signal. 2. Select the brightness on the P-MODE screen. 3. The black level must be changeable with the UP/ DOWN key. 1. Receive the NTSC colour bar signal. (A/V) 2. Select the tint on the P-MODE screen. 3. The tint must be changeable toward green with the UP key and toward red with the DOWN key. 1. Press the NOR. key on the P-MODE screen to make sure all the displayed items are at normal settings. See below for the normal settings. » Contrast » Colour » Brightness » Tint » Sharpness : MAX : CENTER : CENTER : CENTER : CENTER * The contrast, colour, brightness, tint and sharpness settings are all normal when these items do not appear on the screen. Waveform and others
2
COLOUR key
2
High-voltage protector
1. Receive the E-5CH (monoscope pattern) signal. 2. Connect the bias box to the cathode (R635 side) of D607. 3. Adjust the bias box voltage to 18 V and make sure that the protector is not activated. 4. Adjust the bias box voltage to 27 V and make sure that the protector is not activated. 1. In checking the performance of other protectors � for example, the one against shorting of smoothing electrolytic capacitor of +B line �, pay attention not to damage or deteriorate any related element.
3
BRIGHTNESS key
3
Other protectors
4
TINT key
5
PIC-NOR. key
10
A/V INPUT AND OUTPUT CHECK
No. Adjusting point 1 Video and audio output check Adjusting procedure/conditions 1. Receive the E-12CH colour bar (100% white colour bar, 400 Hz, 100% modulation audio) signal. 2. Terminate the video output with a 75 ohm impedance. Make sure the output is as specified (1.0 Vp-p ±3 dB). 3. Terminate the audio output with a 10k ohm impedance. Make sure the output is as specified (1.76 Vp-p ±3 dB). Waveform and others 6 SHARPNESS key
1. Receive the E-5CH signal. 2. Select the sharpness on the P-MODE screen. 3. The sharpness must be changeable with the UP/ DOWN key.
7
Channel sign display colour
1. The display colour of all the channel (0-99) signs must be green. Keep the AFT on.
2
Video and audio input check
1. Using the TV/AV key on the remote controller, make sure that the modes change in the order of TV, AV1, AV2 and TV again and that the video and audio outputs are according to the input and output terminals for each mode.
|
|
|
> |
|
