|
Who's Online
There currently are 6031 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
;
Great manual very clear copied. You are making an incredible job. I appreciate a lot the rapidity and your efficiency. Thanks a lot
;
Good pdf of the service manual for this unit. Includes disassembly instructions, full schematics, board layouts, parts lists and diagnostic information. Some information is in the pdf twice (single pages, and split pages), but that could be how it was originally generated by panasonic, or perhaps the idea is to make it eaiser to put onto 8.5 x 11" pages.
Information was exactly what I needed. Delivery was overnight (less than 12 hours) and I was happy with the process.
;
5 STARS for FAST DELIVERY, BEST PRICES and QUALITY PRODUCT. Item was exactly as described with superb resolution. Will definitely source all my future requirements from this website. Thanks a lot owner-manual.com!
;
OEM manual provided all schematics, board layouts and component specs necessary to facilitate unit maintenance. All pages were clear and readable.
SETTING CLOCK RESETTING THE MICROCOMPUTER
EQUALIZER q To erase all of the stored memory contents (clock and timer (Main unit operation) tem. X-BASS/ settings, tuner and CD presets). DEMO q If the display is not correct.
Reset microcomputer under the following conditions: In this example, clock is set for the 12-hour (AM 12:00) sys-
q If the operation is not correct.
MEMORY/SET
POWER Within 5 seconds, press the MEMORY/SET button. ON/
1
Press ON/STAND-BY button to enter the stand-by mode.
2 Press the CLOCK button. 1 Press ON/STAND-BY button to enter the stand-by mode. 3 2
ON/ BASS/DEMO button, hold down the ON/STAND-BY button for STAND-BY at least 1 second. Press TUNING/TIME ( or ) button to select the time
POWER STAND-BY While pressing down button and the EQUALIZER/X-
4
(AM 12:00 PM 11:59) Caution: TIME (AM 0:00 PM 11:59) memory including clock timer settings, tuner and CD
presets. "0:00" � The 24-hour display will appear.
display mode. q "CLEAR AL" will appear.
CLOCK "AM 12:00" � The 12-hour display will appear. TUNING/
"AM 0:00" � 12-hour display appear. q The operation explained above will erase all data stored in ( ) (0:00 23:59)
q Note that this can only be set when the unit is first installed
or it has been reset (see page 15).
2
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
q When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
3
4 minutes.
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( o r ) button to adjust the
OPERATION MANUAL
�5�
q Press the TUNING/TIME ( or ) button once to advance
q The hour setting will not even if minutes advance from
by 1 minute. Hold it down to change the time in 5 minute intervals. 12:00 AM 0:00
"59" to "00".
q The clock starts operating from "0" second.
9 Press the MEMORY/SET button. 5
(Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
q The time display will appear for about 5 seconds.
6
Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power
failure occurs or after the AC power cord is disconnected.
7
If this happens, follow procedure below to change the clock time.
To change the clock time:
8 xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button.
9 zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
CD-BA120/125
yPerform steps 1 9 above.
|
|
|
> |
|