There are currently no product reviews.
Very detailed product, also it is a scanning from original, very useful if you have to service this type of amplifier ! Very good product, very hard to find!
the Manual was made available as promised, the scans were excellent..Good Work !!!
It's complete and helpful manual with good quality of scan. Thanks very much.
The service was quick and simple, finding the service manual easy and it appears to be the original with colour schematics. It contained the info I was after and so sorted the problem.
I have copied it to CD and attached the envelope to the inside back cover of the owners manual. Good manual and excelent service. Robin Wood, Wood Electronics, New Zealand.
Exactly what was needed to assess the product - excellent value and great service
SETTING THE CLOCK PREPARATION FOR USE
1 Press ON/STAND-BY switch to enter the stand-by mode.
Press CLOCK button. Replace the batteries if control distance decreases or oper(0:00) system. Within 3 seconds, press the MEMORY/SET button. Notes concerning use: In this example, clock is set for the 24-hour
Exposing sensor on the main unit to strong light may in"0:00" â The 24-hour display will appear. terfere with operation. Change lighting or the direction of 0.2 6 m (8" 20') "AM 0:00" â The 12-hour display will appear. Keep the remote control away from moisture, excessive heat,
ON/ display. STAND-BY
4 Press TUNING/TIME ( or ) button to select time and sensor on the main unit with a soft cloth.
ation becomes erratic. Periodically clean transmitter LED on the remote control
CLOCK (0:00 23:59) the unit.
MEMORY/ (AM 0:00 PM 11:59) shock, and vibrations. SET "AM 12:00" â The 12-hour display will appear. 1
(AM 12:00 PM 11:59) Press the MEMORY/SET button. ( )
5 6 Press TUNING/TIME ( or ) button to adjust the hour. 2 7 Press the MEMORY/SET button.
Press ON/STAND-BY (POWER) switch to enter the standtions:Reset microcomputer under the following condiPress TUNING/TIME ( o r ) button to adjust the minutes. Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change automatically to "PM".
RESETTING THE MICROCOMPUTER
3 8 1 4
0:00 AM 12:00
The clock starts operating from "0" seconds. (Seconds are not displayed.) Note: is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure If this happens follow procedure below to change the clock time.
Press button for at least 0.5 seconds to change time To erase all of the stored memory contents (clock in 5 minute intervals. timer settings, tuner and CD presets). Press and hold down VOLUME button, the The hour setting will even if minutes advance If display is not correct. button and ON/STAND-BY (POWER) switch all at the from "59" to "00". same time. Hold them for at least 1 second. If the operation is not correct.
5 9 Press the MEMORY/SET button.
To change the clock time: 8
6 In event of a failure or when the AC power lead
7 occurred or when the AC power lead was disconnected.
1 Press the MEMORY/SET button. 2 Perform steps 6 9 above. 9 1 Press the CLOCK button. 2 Within 3 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.
To see time display: (When the power is ON)
Press the CLOCK button. The time display will appear for about 3 seconds. When the ON/STAND-BY switch is set to ON.
When the ON/STAND-BY switch is set to STAND-BY.
To switch the time display mode:
1 Press ON/STAND-BY switch to enter the stand-by mode. 2 Press and hold down VOLUME button, the
button and ON/STAND-BY switch all at the same time. Hold them for at least 2 second. (Refer to RESETTING THE MICROCOMPUTER on page 16.)
3 Perform steps 1 9 above.
Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.