|
Who's Online
There currently are 6005 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It was just what I needed. Thanks for your quick action and great price. You guys are top notch.
Thanks
;
Excellent manual, complete, great resolution, easy to read especially the schematics. Thank you !
;
Fast delivery, excellent resolution and complete. And above all, the best price ever !
;
Vielen Dank,
das war eine prima Sache. Habe das Serviceheft nach 3 Stunden herunterladen können. Qualität OK. Hat mir mit Erfolg bei der Fehlersuche und Reparatur meines
Nordmende Galaxy Mesa 9000 geholfen. Ich kann diesen Service bestens weiterempfehlen
A very good service.
Thank You!
;
everything i needed. it was easy to get. and this site is now my go to site for manuals.
SETTING CLOCK RESETTING THE MICROCOMPUTER
(Main unit operation) 1,2
In this example, clock is set for q To erase all of the stored memory contents (clock and timer Press the CLOCK button.
Reset microcomputer under the following conditions:
24-hour (0:00) system. settings, tuner and CD presets). Press ON/STAND-BY button to enter the stand-by mode.
1 2
Press ON/STAND-BY button to enter the stand-by mode.
ON/ Press TUNING/TIME ( or ) button to select the time STAND-BY display mode. While pressing down VOLUME button and the oniy
3 Within 5 seconds, press the MEMORY/SET button. 2 1 4
Caution: (AM 12:00 PM 11:59) q The operation explained above will erase all data stored in CLOCK "AM 0:00" � The 12-hour display will appear. memory including clock timer settings, tuner and CD (AM 0:00 PM 11:59) presets.
or it has been reset (see page 23).
q If the display is not correct. q If the operation is not correct.
CD-C421H / C411H
2
TUNING/TIME button, hold down the ON/STAND-BY button
TUNING/
for at least 1 second. SET ( ) "AM 12:00" � The 12-hour display will appear.
"0:00" � The 24-hour display will appear. TIME MEMORY/ (0:00 23:59)
q Note that this can only be set when the unit is first installed
2 5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, "AM" will change automatically to "PM".
3 q Press the TUNING/TIME ( or ) button once to advance 7 Press the MEMORY/SET button.
Press TUNING/TIME ( o r ) button to adjust the minutes. q Press the TUNING/TIME ( or ) button once to advance
4
12:00 AM 0:00 8
5
by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not even if minutes advance from
OPERATION MANUAL
�6�
6 "59" to "00". 9 Press the MEMORY/SET button.
q The clock starts operating from "0" seconds. (Seconds are not displayed.)
7 8
Note: q In event of a failure or when the AC power lead is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.
9
To change the clock time:
When unit is in the stand-by mode: x Press the MEMORY/SET button. y Perform steps 6 9 above. When the unit is on: x Press the CLOCK button. y Within 5 seconds, press the MEMORY/SET button. z Perform steps 6 9 above.
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds.
To change the time display mode:
x Perform steps 1 2 in the section "RESETTING THE MICROCOMPUTER", on page 23. y Perform steps 1 9 above.
|
|
|
> |
|