There are currently no product reviews.
A good manual! fast service and good qualityi for pdf document.
Very helpful and complete manual. Maybe only one negative is schematics have sometimes unreadable name of the parts. But it's not a big problem.
Excellent high quality schematics brought my old Heidelberg back to life. Fast download at a reasonable price. Thanks.
This document is just what I was looking for, itΒ΄s very useful, it contains adjustment procedures for the final stage of the power amp and also
has a complete wiring diagram and description of the main semiconductors used in the design.
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
SETTING THE CLOCK PREPARATION FOR USE
Notes concerning use: Press ON/STAND-BY switch to enter the stand-by mode. Replace the batteries if control distance decreases or oper-
and sensor on the main unit with a soft cloth.
In this example, clock is set for the 24-hour Press the CLOCK button. ation becomes erratic.
3 Within 3 seconds, press MEMORY/SET button. Periodically clean transmitter LED on the remote control 4
(8" 20') CLOCK Keep the remote control away from moisture, excessive heat, shock, and vibrations.
1 1 5 SET "AM 12:00" â The 12-hour display will appear.
ON/ Exposing sensor on the main unit to strong light may indisplay mode. STAND-BY terfere with operation. Change lighting or the direction of 0.2 6 m
Press TUNING/TIME ( or ) button to select the time
(0:00 23:59) (AM 0:00 PM 11:59) MEMORY/ (AM 12:00 PM 11:59)
"0:00" â The 24-hour display will appear. the unit.
"AM 0:00" â The 12-hour display will appear.
Press the MEMORY/SET button. ( )
6 Press TUNING/TIME ( or ) button to adjust the hour.
Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change automatically to "PM". RESETTING THE MICROCOMPUTER
To erase all of the stored memory contents (clock and timer Press TUNING/TIME ( o r ) button to adjust the
7 Press MEMORY/SET button. Reset microcomputer under the following conditions: 8
The hour setting will not even if minutes advance
4 minutes. settings, tuner and CD presets).
0:00 AM 12:00 If the operation is not correct. 2
Press button for at least 0.5 seconds to change the time If the display is not correct. in 5-minute intervals.
from "59" to "00". Press ON/STAND-BY (POWER) switch to enter the stand-
5 9 Press the MEMORY/SET button.
6 In event of a failure or when the AC power lead
The clock starts operating from "0" seconds. (Seconds are Press and hold down VOLUME button, the not displayed.) button and ON/STAND-BY (POWER) switch all at the Note: same time. Hold them for at least 1 second.
7 occurred or when the AC power lead was disconnected.
is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure
If this happens, follow procedure below to change the clock time.
To change the clock time: 8
1 Press the MEMORY/SET button. 2 Perform steps 6 9 above. 9
When the ON/STAND-BY switch is set to STAND-BY.
1 Press the CLOCK button. 2 Within 3 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.
When the ON/STAND-BY switch is set to ON.
To see time display: (When the power is ON)
Press the CLOCK button.
The time display will appear for about 3 seconds.
To switch the time display mode:
1 Press ON/STAND-BY switch to enter the stand-by mode. 2 Press and hold down VOLUME button, the
button and ON/STAND-BY switch all at the same time. Hold them for at least 2 seconds. (Refer to RESETTING THE MICROCOMPUTER on page 17.)
3 Perform steps 1 9 above.
Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.