There are currently no product reviews.
Manuale perfetto. Ottimo e utilissimo. Grazie a questo manuale ho potuto realmente risolvere il complesso problema della stampante.
Was very fast and accurate service. Just what I needed. I recommend to everyone.
Very good scan quality, only PC Board scan not enough contrast.
First of all I must say that I received the manual in just a few minutes after placing the order. The copy is well done ββand very readable. I will buy others soon... Thanks, Meyer
Good service manual. I gat all I want. Copy is good, but could be better. All clear and useful. I sincerely recommend.
SETTING THE CLOCK PREPARATION FOR USE
In this example, clock is set for the
Replace the batteries if control distance decreases or oper24-hour (0:00) system.
1 Press ON/STAND-BY switch to enter the stand-by mode. Notes concerning use: 2 3
Periodically clean transmitter LED on the remote control Within 5 seconds, press the MEMORY/SET button. and sensor on the main unit with a soft cloth. ON/
Press the CLOCK button.
ation becomes erratic.
STAND-BY Press TUNING/TIME ( or ) button select time Exposing sensor on the main unit to strong light may
"0:00" â The 24-hour display will appear. (8" 20')
"AM 12:00" â The 12-hour display will appear. 1 5 (AM 12:00 PM 11:59) ( ) (AM 0:00 PM 11:59)
Keep the remote control away from moisture, excessive heat,
CLOCK 0.2 6 m of the unit.
(0:00 23:59) "AM 0:00" â The 12-hour display will appear.
display mode. interfere with operation. Change lighting or the direction
shock, and vibrations.
Note that this can only be set when the unit is first installed or it has been reset (see below).
5 Press the MEMORY/SET button. 2 6 Press TUNING/TIME ( or ) button to adjust the hour.
Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously.
4 matically to "PM". RESETTING THE MICROCOMPUTER
When the 12-hour display is selected, "AM" will change auto-
0:00 AM 12:00 Reset microcomputer under the following conditions:
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( o r ) button to adjust the To erase all of the stored memory contents (clock and timer
If the operation is not correct.
5 Press button for at least 0.5 seconds to change the time
from "59" to "00". Note:
minutes. settings, tuner and CD presets).
If the display is not correct. in 5-minute intervals. The hour setting will not even if minutes advance
1 2 6
To tuner preset memory, see "To erase all of the
9 Press the MEMORY/SET button. contents of preset memory" on page 15. 2
The clock starts operating from "0" seconds. (Seconds are
7 not displayed.) 1 Press ON/STAND-BY switch to enter the stand-by mode.
8 is disconnected, the clock display will go out. them down for at least 1 second.
Note: Press VOLUME button, the TUNING/TIME button In event of a failure or when AC power lead and ON/STAND-BY switch all at the same time. Hold
9 If this happens, follow procedure below to change the
When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure occurred or when the AC power lead was disconnected.
switch time display mode: To change the clock time:
Press ON/STAND-BY switch to enter the stand-
When the ON/STAND-BY switch is set to STAND-BY. When unit is in demonstration mode, press the DEMO button to enter the clock mode.
2 Press VOLUME button, the TUNING/TIME Press the MEMORY/SET button.
button and ON/STAND-BY switch all at the same 2 Perform steps 6 9 above. time. Hold them down for at least 1 second. (Refer RESETTING THE MICROCOMPUTER on When the ON/STAND-BY switch is set to ON. page 27.) Press the CLOCK button. 1
Within 5 seconds, press the MEMORY/SET button.
Perform steps 1 9 above.
Perform steps 6 9 above.
To see time display: (When the power is ON) The operation explained above will erase all data
stored in memory, such as clock and timer settings, Press the CLOCK button. tuner and CD presets. The time display will appear for about 5 seconds.