|
Who's Online
There currently are 5637 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Readable text and good copy. Very much needed if you wish to do some repairs on this fine old unit.
;
Fint forløb med levering af manualen. Kvaliteten af skanningen betegnes som middel
;
I found the manual to be clear concise and complete. It was of immense assistance when removing the unit as the unit was over 22 years old and the wiring diagram was unobtainable from the manufacturer. The exploded drawings were clear as were the instructions and labels.
;
I will highly recommend this seller. They are honest, accurate, fast and responsible.
;
This manual was very good & was very helpful with repairs.
Always great & fast service from Owner's manual.
CD-E100H CD-E100E
REMOVING AND REINSTALLING THE MAIN PARTS
TAPE MECHANISM SECTION
Perform steps 1 to 6 and 9 of the disassembly method to remove the tape mechanism.
(A1)x1 ø2x7mm Hook (A2)x2
TAPE 1
(A1)x1 ø2x3mm Record/Playback Head
How to remove the record/playback and erase heads (TAPE 1) (See Fig. 7-1)
1. When you remove the screws (A1) x 2 pcs., the record/ playback head can be removed. 2. Move the hooks (A2) x 2 pcs., toward the center position as shown in Fig. 7-1 and then lift the erase head.
How to remove the playback head (TAPE 2) (See Fig. 7-2)
1. When you remove the screws (B1) x 2 pcs., the playback head can be removed.
Erase Head
Figure 7-1
How to remove the pinch roller (TAPE 1) (See Fig. 7-3)
1. When you remove the screw (C1) x 1 pc., the pinch roller can be removed. Note: When installing the pinch roller, pay attention to the spring mounting position.
(B1)x1 ø2x6mm
(B1)x1 ø2x6mm
TAPE 2
Playback Head
How to remove the pinch roller (TAPE 2) (See Fig. 7-3)
1. When you remove the screw (D1) x 1 pc., the pinch roller can be removed. Note: When installing the pinch roller, pay attention to the spring mounting position.
Figure 7-2
TAPE 1
(C1)x1 ø2x4mm
TAPE 2
(D1)x1 ø2x4mm
How to remove the tape motor (See Fig. 7-4)
1. Remove the belt. 2. Remove the screws (E1) x 6 pcs., to remove the motor bracket. 3. Remove the screws (E2) x 3 pcs., to remove the tape motor.
Pinch Roller
Pinch Roller
How to remove the belt (TAPE 1) (See Fig. 7-5)
1. Remove the main belt (F1) x 1 pc., from the tape motor side. 2. Remove the FF/REW belt (F2) x 1 pc.
Tape Motor
Figure 7-3
(E1)x2 ø2x4mm (E1)x2 ø2x4mm
How to remove the belt (TAPE 2) (See Fig. 7-5)
1. Remove the main belt (G1) x 1 pc., from the tape motor side. 2. Remove the FF/REW belt (G2) x 1 pc.
(E1)x2 ø2x4mm
Tape Motor TAPE 2 Main Belt (G1)x1 FF/REW Clutch Ass'y Tape Motor TAPE 1 Main Belt (F1)x1
Motor Bracket
TAPE 2
Main Belt (G1)x1
(E2)x3 Special Screw
TAPE 1
FF/REW Belt (F2)x1 FF/REW Clutch Ass'y FF/REW Belt (G2)x1 Main Belt (F1)x1
Motor Bracket
Tape Motor
Figure 7-4 �7�
Figure 7-5
|
|
|
> |
|