|
|
|
Who's Online
There currently are 5974 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
DV-650 DV-650W
5. Disassembling the loading drive system (1) Remove the two M2 screws A . (2) Remove the tray pinion B . (3) Remove the relay gear 1 C together with the timing belt S D . (4) (5) (6) Remove relay gear 2 E . Remove the two M1.7 screws F . Remove the L motor G (with pulley) downward.
M2 A
M1.7 F L·Motor Pulley L·Motor G
Relay Relay gear1 gear2 C D E
Tray pinion B
Timing belt S
6. Disassembling the mechanism chassis from the moving chassis (1) Remove the insulator B (2 pcs. at the right side in diagram) parallel in the arrow direction. (At this time it is better to insert the fine head of screw driver at the ID side of insulator and to move in the arrow direction, which facilitates removal.) (2) Remove the mechanism chassis in the arrow direction, pulling upward aslant. At this time take care so that the insulator C (left side, 2 pcs.) is not damaged. (Do not put at once the mechanism chassis assembly.) Insulator C
Insulator B
Mechanism chassis P tight screw with M2.6 washer A
Insulator
C
Insulator
B
7. Replacing the pickup and the spindle motor Since the pickup optical axis and turntable inclination of DVD are adjusted with higher accuracy than of CD/MD, make a replacement as a mechanism service chassis ass'y (refer to Parts List). Mecha chassis Ass'y
8. Replacing the Sled Motor (1) At the rear side of chassis remove the two M1.7 screws A , and remove the motor angle B . (2) Remove the thrust holding screw C (for easier removing wipe off the thread lock). (3) Remove the two motor fitting screws M1.4 D , and replace the motor E . Motor is replaced in the state while the worm F is kept press-fitted to the output shaft. Note: When installing the motor, take care so that the worm does not damage the ANG B hole. (4) Screw in the thurust holding screw C , adjust the worm front end clearance to 0 to 0.1 mm, and apply screw lock.
Apply screw-lock.
Thurust holding screw Motor Angle
C B
M1.7 screw A M1.4 screw D
Sled motor E Worm F
6-3
|
|
|
> |
|
