|
|
|
Who's Online
There currently are 5646 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
DVD SETUP Audio Setting (digital output only)
Choose the appropriate Audio settings for your music equipment.
Display Setting
You can change certain aspects of the DVD�s display screens, on-screen messages and the display panel on the front of the DVD player. 1 Press SETUP during playback is stopped. 2 Press K or L to select DISPLAY, then press
NOTE:
� These audio settings are effective only when using a digital connection. Although you may change the settings from the on-screen display, these audio settings do not actually affect the sound when using an analogue connection. 1 Press SETUP during playback is stopped. 2 Press K or L to select AUDIO, then press ENTER. 3 Press K or L to choose the below items and press
ENTER.
3 Press K or L to select the below items, then press
ENTER.
TV Aspect
16
Aspect ratio of the received signal.
ENTER repeatedly to turn the setting ON or OFF. Dynamic Range Control (DRC):
� The default setting is OFF. � To compress the range of sound volume.
9
Dolby Digital :
� The default setting is Bitstream. (Bitstream : Output by Dolby Digital) (DPCM : Convert the Dolby Digital to D-PCM) Set to Bitstream when the unit is connected to Dolby Digital Decoder. � Press K or L for an item selection, then press ENTER. 4 � Select 4:3 LETTER BOX for a black bars appears on the top and bottom of the screen. 3
DTS:
� The default setting is OFF. Set to On when the unit is connected to DTS Decoder. (On: Output by DTS)
4
� Select 4:3 PAN & SCAN for a full height picture with both sides trimmed.
MPEG:
� The default setting is OFF. (On : Output by MPEG sound) (OFF: Convert the MPEG to PCM) Set to On when the unit is connected to MPEG Decoder.
3
16
� Select 16:9 WIDE if a widescreen TV is connected to the DVD player.
DOWN SAMPLING:
� The default setting is AUTO. � Press ENTER, then K or L to select AUTO, 48kHz or 96kHz. Press ENTER again to confirm selection. � Select 96kHz if the disc was recorded in PCM 96kHz, otherwise select 48kHz. 4 Press SETUP to exit.
9
Panel Display
� Press K or L to select BRIGHT, DIMMER and AUTO, then press ENTER. � This adjust the brightness of the display panel with the factory default BRIGHT. � When AUTO is selected, the display dims only during playback.
Black Level Setting
Adjust the Black Level Settings to make the black parts of the picture as bright as you preferred. 1 Press MODE during playback. 2 Press ENTER repeatedly to select ON or OFF. ON: makes the dark parts brighter. OFF: shows the original picture as recorded.
Angle Icon
� Press ENTER repeatedly to turn Angle icon ON or OFF. � The default setting is ON.
Auto Power Off
Auto Power Off:
� Press ENTER repeatedly to turn Auto Power ON or OFF. � The default setting is ON and it will turn the DVD player to off automatically after 35 minutes of no use. 4 Press SETUP to exit.
NOTE:
� Black Level Setting is not available if your TV is set to receive the RGB signal (see page 8 for more infomation).
� 18 �
EN
 $4.99 DVS1SY SHARP
Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|
