|
Who's Online
There currently are 5921 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The ease of this purchase was a good start. The content of this manual was exactly all I needed to retore my Tandberg 64.
All of the mechanical and electrical information is contained in the manual and the quality of the document makes reading the data easy.
The exerience with the resource has made this my prime source for technical data.
;
Owner-manuals.com is the best Possibility to give vantage HIGH CLASS Elektronic COMPONENTS
a new Life.Thanks alot for your perfekt Service.
;
I am proud of you. In the future, I benefited from your services.
;
I found this manual to be complete in every detail. Besides the schematic it has a complete set of alignment instructions which are easy to understand. It also includes a complete parts list as well as an explanation of how the power supply and safety shutdown circuits operate. Even a schematic of the tuner is included.
;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
PG-C30XE
ADJUSTING THE PC BOARD (CPCi-0047CE02. PC I/F Unit)
1. Setting the oscilloscope Set the range to DC 1 V/div and 5µs/div. 2. Connecting the PC interface 1) Connect the PC interface to the projector. Make surethe CON2 (P8404), CON3 (P8502) and CON4 (P8405)connectors are all tight in position. 2) Connect the cable between the computer�s ANALOG OUTPUTterminal and the DSUB (INPUT1 on the projector)connector. 3) Set the projector�s input selector to the RGB1position. 4) Set the signal generator to the XGA mode (1024 x 768, 60Hz, 32-tone scale). Keep the output amplitude at 700mVp-p. 5) Turn on the power. 3. Adjusting the levels and checking the tones 1) Press the SW5101 switch to call up the process mode. 2) Enter 8 for the SH-PHASE setting on the OUTPUT3 menu. (Adjust to get the on-screen display characters clearand crisp.) (A/D menu adjustment) 3) R-BRIGHT adjustment: Feed the black signal and adjust the R-BRIGHT setting on the A/D menu screen until the bitless state. 4) G-BRIGHT adjustment: Feed the black signal and adjust the G-BRIGHT setting on the A/D menu screen until the bitless state. 5) B-BRIGHT adjustment: Feed the black signal and adjust the B-BRIGHT setting on the A/D menu screen until the bitless state. 6) R-D adjustment: Feed the white signal and adjust the R-D setting on the A/D menu screen until the bitless state. 7) G-D adjustment: Feed the white signal and adjust the G-D setting on the A/D menu screen until the bitless state. 8) B-D adjustment: Feed the white signal and adjust the B-D setting on the A/D menu screen until the bitless state. 4. DTV adjustment 1) Feed the 480P Y signal to INPUT1. Keep the R (Pr) and B (Pb) without signal input. 2) G-BRIGHT adjustment: Make this setting the same as the G-BRIGHT setting on the A/D menu screen. 3) CR-OFFSET adjustment: Feed the 56% white signal and adjust the CR-OFFSET setting on the DTV menu screen until the bitless state. 4) CB-OFFSET adjustment: Feed the 56% white signal and adjust the CB-OFFSET setting on the DTV menu screen until the bitless state. 5) G-BRIGHT correct adjustment = Adjust the value of G-BRIGHT up 6 point. 6) Press SW5101 and exit from the process mode.
Servicing precautions
If the convergence gets out of spec in servicing the set, call the process mode and select the following group and subjects. Group: NOKO Subject: R-CNV-H, R-CNV-V G-CNV-H, G-CNV-V B-CNV-H, B-CNV-V (H and V are for horizontal and vertical adjustments, respectively.) Adjust the above settings to the range of 0 to 4.
28
|
|
|
> |
|