|
|
|
Who's Online
There currently are 5815 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
14. Re-insert the paper cassette.
Lift up on both sides of the back of the paper cassette and, while aligning the right guide on the cassette with the guide rail as shown in the figure, push the cassette into the desk along the guide rails. After doing this, confirm that the cassette moves in and out smoothly.
Guide rail
�
If the mode is to be set for a combination of optional equipment, add together the setting values shown in the table below for each peripheral device, and set the mode to the total setting value. For example, to set the mode for a combination of the SF-D20 and the SF-S53, the total setting value is 4 + 10 = 14, so the key operation sequence is as follows.
READY
1
4
Guide
SF-A17/A56
1
SF-D20/D21
4
Sorter
10
5 For the SF-D21
(The initial paper size setting is A4 for the AB system and 8 1/2 x 11 for the inch system.)
17. Pull out the large-capacity paper cassette. 15. Place the paper in the cassette.
Place the paper in the paper cassette. When doing this, do not stack the paper higher than the maximum height line indicated on the cassette. Next, push the cassette all the way into the desk as far as it will go.
Maximum height line
Lift up on the handle on the paper cassette and pull the cassette out from the desk until it stops (the paper loading position), and then lift up on the casette handle once again and pull the cassette all the way out of the desk.
18. Adjust the positions of the front and rear paper guides. 16. Set the mode. � Operate the keys on the copier to set the mode.
READY
INTERRUPT INT ERRUPT
Remove the mounting screws which secure the front and rear paper guides, fit the two paper guides into the appropriate positions corresponding to the desired paper size, and then also secure the mounting screws into the holes corresponding to the desired paper size.
Rear paper guide
READY
C
0/
2
6
Front paper guide
0/
1
The above sequence of key operations will display the current setting value.
�
If only the SF-D20 is being set, immediately after the above key operation sequence, perform the following key operation sequence to set the mode.
READY
0/
4
5 � 33
 $4.99 SF2530 SHARP
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…  $4.99 SF-2530 SHARP
Parts Catalog Parts Catalog only. It's available in PDF format. Useful, if Your equipment is broken and You need t…
|
|
|
> |
|
