|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
NO.11 CAPSTAN TROUBLESHOOTING FLOW CHART NO.13 DRUM MOTOR TROUBLESHOOTING(2)
VC-H63M
capstan fails to run. The drum motor runs only for a few seconds.
NO the capstan error Is drum PG signal given out from IC801. Check drum motor.
pin(45) IC801. pin(3) of AD connector?
YES and all the way up thru to pin(13) of Check AT 5V line. Check line between AD connector Is the voltage of 5V DC applied at NO pin(8) of AE connector? IC801. Check line between AD connector Check line between the AE connector Is drum FG signal given out at NO sent in pin(4) of AE connector? pin(12) of IC801? of IC801. of IC801. Check pin(35) of IC801 and all the Is head switching pulse given out at NO NO way up thru to the current limitter line pin(38) of IC801? of R854~858. Is the voltage pin(3) of AE Check IC801. connector 1.25~2.5V? Check M 12V line. Replace capstan motor.
Is drum PG signal given out at pin(13) of IC801?
YES
Is the voltage more than 2.6V DC NO
and all the way up thru to pin(47) and all the way up thru to pin(12)
YES YES
YES
NO
Is the M 12V applied at pin(5) of Replace IC801. AE connector? YES
40
Is the drum motor rotating? NO
pin(44) of IC801? Check IC801.
FLOW CHART NO.12 DRUM MOTOR TROUBLESHOOTING(1) FLOW CHART NO.14 HEAD SWITCHING PULSE TROUBLESHOOTING
The drum motor fails to run. No head switching pulse.
Is the drum error signal given out of NO See FLOW CHART NO.12,13 DRUM MOTOR
YES TROUBLESHOOTING(1), (2)
YES pin(3) of IC801? NO
Check M 12V line. YES about 5Vp-p D-PG
Is the voltage more than about 1.3V Check line between R836 (Drum NO Is the PG signal and drum FG DC given out pin(7) of AD error filter) and all the way up to signal present on the pins(13) and connector? pin(7) of AD connector. (12) of IC801, respectively?
Are there drum PG M.M. signal at NO YES NO YES
Is the M 12V applied at pin(4) of AD NO D-FG Check C835 and readjust R875. connector? (HEAD SW. POINT control.)
Replace drum motor. Replace IC801.
about 5Vp-p Check line between AD plug and all the way up thru to IC801. NO Check drum motor and between AD to AO harness. Are the PG signal and drum FG YES signal present on pins(3) and (5) of AD connector?
|
|
|
> |
|