|
|
|
Who's Online
There currently are 5644 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
VL-FD1U
8-4. Running rough adjustment
(Since this adjustment is performed without cassette controller, put a proper weight so that the cassette does not rise , and make an adjustment.) 1) Su, Tu guide roller height adjustment <Method and description> (1) Loosen the guide roller lock screw, then tighten loosely so that the roller turns easily. (2) Replay an alignment tape, and adjust the Sup, Tu guide roller so that the envelope sides of entrance and exit are flat. (3) Perform ± 1/4 shift, then, as in the above case, adjust until the envelope becomes flat. * If running is difficult for the entrance changed, turn the T roller to counter clockwise 180°. (refer to Fig. 1)
NG ±1/4 shift Entrance side Normal Exit side NG ±1/4 shift
Turn to 180° T roller
Fig. 1
2) Check of V/SR envelope wave form <Method and description> (1) Confirm that the envelope waveform peaks in V/SR mode are uniform. (2) If they are not uniform, fine-adjust the guide roller and the Tu guide. 3) Check of tape wrinkles <Method and description> (1) Check that the tape is not distorted between the Tu guide and pinch in the PB mode and the V/SR mode. -If crease is found, make an adjustment in the range of ±180°. -After adjustment apply Screw Lock.
Pinch roller
Adjust so that A
A
�
�
B.
B
Wrinkles Tu guide
Deformation
Deformation
4) Check the rising time of the envelope wave form <Method and description> (1) Check the rising time of the envelope when switching from V/SR mode to PB mode. (Within 5 sec) (2) Check the rising time of the envelope when switching from STOP mode to PB mode. (Within 5 sec)
8-5. Final running adjustment
(Perform adjustment without removing the cassette controller.) 1) Adjustment of Sup and Tu guide roller height <Method and description> (1) Perform ± 1/4 shift, then if the envelope wave's ratio of MAX. to MIN. are 60% or less, adjust again the height of guide roller. (Refer to Fig. 2) (2) Finally adjust the lock screw of Sup and Tu guide roller. (3) Once perform unloading and then loading to set the PB mode, and make sure that the envelope waveform does not change. 2) Adjustment of playback SWP <Method and description> (1) Playback the alignment tape for switch point adjustment. (2) Perform SWP automatic adjustment with adjustment remote control. * When replacing the mechanism and drum, adjust the phase and equalizer using the adjustment remote control. (Refer to "10. ADJUSTMENT THE ELECTRICAL CIRCUIT".)
EMIN EMAX
EMIN EMAX
Fig. 2
60 (%)
16
|
|
|
> |
|
