|
Who's Online
There currently are 5861 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
VN-EZ1C
VN-EZ1U
4. DISASSEMBLY OF THE SET
~For assembly, tighten the screw to the torque of 0.5+0.1/-0 kg cm. ~Previously remove the smart medium unit. 1. Front cabinet 6. H x2
2
SHUTTER PWB C G C
C
Battery lid B 1 A x1 H
POWER PWB MAIN PWB
· Remove the screws ( A LX-BZ0210TAFN)(1pcs.) and ( B LX- · Remove the screws ( C LX-HZ0058TAFF)(2pcs.) and ( G LXHZ0056TAFN)(1pcs.) and ( H LX-BZ0208TAFN)(3pcs.). HZ0206TAFN)(1pcs.). · Open the battery lid as instructed with 1. · Pressing the power PWB to prevent it from floating, lift the main · Remove the front cabinet, lifting it as instructed with 2. PWB in the arrow direction. (Take care that the board-to-board connector is slightly inner than the center.) 2. D x2 · Remove the screw ( C LX-HZ0058TAFF) of the shutter PWB, D x2 and the main PWB will be removed.
Lens unit
7.
Battery connector
B Tapping Back light connector TFT PWB FFC JACK PWB
MAIN PWB
· Remove the screws ( B LX-HZ0056TAFN)(1pcs.) and ( D LX-
HZ0062TAFF)(4pcs.). · Remove the JAK PWB screw ( D LX-HZ0062TAFF)(1pcs.), the · Lift the lens unit, and remove the CCD flex and tilt connector battery connector, TFT PWB FFC and back light connector, and across the main PWB. the power PWB will be removed. · Remove the operation key flex connector and SP microphone Note: As far as the power PWB is routed to , connect the black lead
connector, and lift the main PWB.
3.
H x2
H x2
wire of the jack PWB directly to the battery terminal. From , solder two lead wires from the battery terminal to the power PWB and the black lead wire from the jack PWB to the land near the battery connector. Lens unit
8.
H x2
H x1
H x2 H x1
· Remove the screws ( H LX-BZ0208TAFN)(7pcs.).
4.
CCD PWB
H x2
· Remove the screws ( H LX-BZ0208TAFN)(3pcs.).
9.
TFT flex
· Remove the screws ( H LX-BZ0208TAFN)(2pc.). · Remove the CCD flex.
5.
· Remove the TFT flex. TFT · Pull off TFT in the arrow direction.
10.
CCD PWB
H x1
TFT PWB
· Remove the CCD PWB.
· Remove the screw ( H LX-BZ0208TAFN), and TFT PWB will be removed.
4-1
|
|
|
> |
|